Applications: Detect either continuous or impulsive vibration or impacts

　　Industries: Engine and Vehicle, Medical, General Industry, Consumer Goods

　　Description: The MiniSense 100 is a low cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Pins are designed for easy installation and are solderable. Horizontal and vertical mounting options are offered. The active sensor area is shielded for improved RFI/EMI rejection. Rugged, flexible PVDF sensing element withstands high shock overload. Sensor has excellent linearity and dynamic range, and may be used for detecting either continuous vibration or impacts. The mass may be modified to obtain alternative frequency response and sensitivity selection (consult factory). The MiniSense 100 acts as a cantilever-beam accelerometer. When the beam is mounted horizontally, acceleration in the vertical plane creates bending in the beam, due to the inertia of the mass at the tip of the beam. Strain in the beam creates a piezoelectric response, which may be detected as a charge or voltage output across the electrodes of the sensor. The sensor may be used to detect either continuous or impulsive vibration or impacts. For excitation frequencies below the resonant frequency of the sensor, the device produces a linear output governed by the "baseline" sensitivity. The sensitivity at resonance is significantly higher. Impacts containing high frequency components will excite the resonance fre-quency, as shown in the plot above (response of MiniSense 100 to a single half-sine impulse at 100 Hz, of amplitude 0.9 g). The ability of the sensor to detect low frequency motion is strongly influenced by the external electrical circuit.

　　Features:

　　Low cost
　　Cantilever-type vibration sensor
　　High sensitivity at low frequencies
　　Active sensor area is shielded for improved RFI/EMI rejection
　　Excellent linearity and dynamic range
　　Rugged, flexible PVDF sensing element withstands high shock overload

　　典型應用: 檢測連續或脈沖振動和沖擊

　　行業: 發動機和機動車輛, 醫療, 工業控制, 消費電子和家用電器

　　產品描述:

　　MiniSense100是一款采用懸臂梁結構的低成本振動傳感器，端部的質量塊使得傳感器在低頻時產生高靈敏度。其插針結構易于安裝和焊接；水平安裝，垂直安裝及短插針可選。傳感器工作區域采用自屏蔽結構，防射頻干擾和電磁干擾。柔性PVDF的一端固定，另一端懸空，使其可以經受高頻的沖擊載荷。傳感器有良好的線性度和動態測量范圍，可以用來監測連續振動和沖擊�？赏ㄟ^調整質量塊的重量達到不同的響應頻率和靈敏度（請咨詢MEAS）。MiniSense100是一款采用懸臂梁結構的加速度計，當水平安裝時，由于慣性的作用，垂直方向的加速度將導致梁的彎曲變形，從而引起薄膜的壓電效應，產生的電荷或者電壓信號通過連接在薄膜上的電極引出。傳感器可以監測連續的或者脈沖的振動或沖擊。對于諧振頻率以下的激勵頻率，MiniSense100會產生很穩定的線性輸出，其值為基線對應的靈敏度值。在諧振頻率時，其靈敏度最大，高頻的沖擊會引起傳感器的諧振。低頻振動的監測很大程度上受到外部電路的影響。

　　特點:

　　低成本
　　懸臂梁式振動傳感器
　　低頻時靈敏度高
　　自屏蔽的動態傳感區域，有效防止射頻干擾和電磁干擾
　　極好的線性度和動態范圍
　　耐高沖擊

　　MiniSense100傳感器更多技術參數及規格書下載請瀏覽：http://ywhs9.com/sensors/341.html

　　北京賽斯維測控技術有限公司產品咨詢熱線：010-84775646，84775648。